Is the stand-alone operating system of MikroTik RouterBOARD hardware. It can also be installed on a PC and will turn it into a router with all the necessary features - routing, firewall, bandwidth, management, wireless access point, backhaul link, hotspot, gateway, VPN server and more. The tutorial explains how to install RouterOS on Qemu virtual disk and configure GNS3 software to run such a router. Later, We will use GNS3 to a create simple testing topology with one RoutersOS router connected to emulated Cisco 3725 router.

You can download Mikrotik RouterOS x86 installed on Qemu and VirtualBox images in the Download section. Software Prerequisites • GNS3 with Qemu or VirtualBox support • Qemu or VirtualBox • RouterOS ISO image - Virtual Machine Prerequisites • i386 compatible architecture • minimum 32MB of RAM (maximum supported 2GB) • minimum Hard Disk space 64MB • Network cards supported by linux v3.3.5 kernel (PCI, PCI-X) RouterOS x86 Installation 1. Download RouterOS for x86 Architecture $ wget 2. Create Qemu Virtual Disk and Start Virtual Machine $ /usr/local/bin/qemu-img create -f qcow2 routeros-6.37.5.img 200M $ / usr/local/bin/qemu-system-i386 -m 512 -enable-kvm -boot d -cdrom mikrotik-6.37.5.iso routeros-6.37.5.img 3. Install RouterOS Use spacebar to select packages that are needed. Then press 'i' to install RouterOS. Picture 1 - RouterOS Installation Once RouterOS is installed, you have 24 hours to enter a license key to activate RouterOS Qemu image.

The timer stops if router is shutdowned. For this reason, we let GNS3 automatically create the copy of base Qemu image every time is a new RouterOS instance placed on the GNS3 desktop. These independent copy of the base image can be run for total 24 hours time period. Start RouterOS Qemu Disk After the disk is formatted and packages copied, start RouterOS instance with the command: $ /usr/local/bin/qemu-system-i386 -m 512 -enable-kvm -boot c routeros-6.37.5.img -nographic -serial telnet::4444,server,nowait You should be able to login to RouterOS with the telnet command: $ telnet 127. Game Emulator V6 0 Aristocrat Slot. 0.0.1 4444 Username is admin without password set. Connect Qemu image to GNS3 I assume that GNS3 is correctly installed and configured.

A) Start GNS3 and create a new GNS3 project Picture 2 - Creating GNS3 New Project b) Configure Qemu guest settings Navigate to Edit ->Preferences ->Qemu ->Qemu Guest and configure parameters as it is shown on the picture below. Picture 3 - Qemu Guest Settings RouterOS Configuration 1. Testing Topology The topology consists of one RouterOS that connects two Qemu instances. As we want to test switching and VLANs, both Microcore instances are connected to RouterOS switvchport that are separated by VLANs - VLAN10 and VLAN20. RouterOS's interface Ethernet1 si connected to Cisco 3725 router emulated. The port will be configured as a trunk port on RouterOS side and as a routed port with two sub-interfaces on Cisco's side.

Picture 4 - Testing Topology 2. Create Bridges for VLAN10 and VLAN20 and Assign Access Ports to Bridges First, check available Ethernet interfaces.They are six Ethernet interfaces presented in RouterOS console in total. Picture 5 - Router Ethernet Interfaces We are going to create bridges br10 and br20 and assign interface Ethernet2 to the bridge br10 and Ethernet3 to br20. [admin@MikroTik] >/interface bridge add name=br10 [admin@MikroTik] >/interface bridge add name=br20 [admin@MikroTik] >/interface bridge port add interface=ether2 bridge=br10 [admin@MikroTik] >/interface bridge port add interface=ether3 bridge=br20 3.

Configure Trunk Port to allow VLAN 10 and VLAN 20 and create Switched Virtual Interfaces - SVI10 and SVI20 [admin@MikroTik] >/interface vlan add vlan-id=10 name=SVI10 interface=ether1 disabled=no [admin@MikroTik] >/interface vlan add vlan-id=20 name=SVI20 interface=ether1 disabled=no Note: the term SVI is used in a Cisco world, feel free to change it if you want. Add SVI Ports to Bridges [admin@MikroTik] >/interface bridge port add interface=SVI10 bridge=br10 disabled=no [admin@MikroTik] >/interface bridge port add interface=SVI20 bridge=br20 disabled=no Picture 6 - Bridge Ports Configuration 5. Assign IP address to SVI Ports This configuration ensures that intervlan routing betwwen VLAN 10 and VLAN20 can be done by RouterOS. [admin@MikroTik] >/ip address add interface=SVI10 address=192.168.10.254/24 disabled=no [admin@MikroTik] >/ip address add interface=SVI20 address=192.168.20.254/24 disabled=no At this point you should be able to make successful ping between PC1 and PC2. Set password and hostname [admin@MikroTik] >/password new-password=admin [admin@MikroTik] >/system identity set name=RouterOS-I 7. Static routing configuration [admin@RouterOS-I] >/ip route add dst-address=10.10.10.10/32 gateway=192.168.10.253 Picture 7 - Routing Table End hosts PC1 and PC2 Configuration End hosts are represent by Microcore Linux 3.8.2 installed on Qemu virtual disks.